Stump Grinding in Fayetteville
You may want to consider a DIY project if you are considering stump grinding in Fayetteville. Even if you use a tree service or landscaping company to remove trees, the price for the contract rarely includes removal of the stump and this task is invariably left to the homeowner. However, have you ever tried digging out a tree stump? You could spend the best part of the using tools like shovels, picks and chainsaws and still not have much luck in getting the stump out of the ground.
Landscaping companies charge according to the size of the stump and you can expect to pay anything from $ 90-$ 150 to remove a stump which is 24 inches in diameter. You can rent a gas powered stump grinder for between $ 100 and $ 200 per day depending on the size of the equipment. If you only have to remove one or two stumps, you're probably better off a professional but if you need to remove more or to share the experience with a neighbour, renting is definitely far more economical. You should make certain that the rental dealer explains the controls to you and shows you the safety precautions in operating the machine. Never use a stump grinder without wearing protection for the eyesight and hearing. You will also need a vehicle with a trailer hitch to to the grinder which has a weight of around 1000 lb but this is not available, your rental dealer will probably deliver the equipment to your house for an additional charge.
Start by using a shovel or a mattock to remove rocks from the base of the stump and this is important because the rocks can affect or damage the teeth on the cutting wheel. Next you will need a chainsaw to carefully trim the stump as close as possible to the ground and this is a step that you can skip and start with the grinder but things go much quicker this way. Use the hydraulic lever to lift the grinder wheel a few inches above the stump and drive the machine forward to position it directly over the front edge. Start the wheel spinning and then slowly lower rate of about 3 inches into the stump. The hydraulic lever can be used to swing the wheel from side to side to clear out the wood. After you are finished at least 4 inches, raise the wheel and advance it a few inches while repeating the process. When the machine is in operation, always position yourself at the control panel which is near the rear of the machine and safely away from the cutting wheel.
Slowly continue to grind your way to the other side of the stump stopping to check that the freshly dug hole is at least 4 inches below the ground. Collect the wood
chips and fill the crater with topsoil. Tamp down the soil and rake it lightly and then spread out an even layer of grass seed raking the seeds into the soil. Water the area and then cover the seats with a thick coating of mulch hay.
Landscaping companies charge according to the size of the stump and you can expect to pay anything from $ 90-$ 150 to remove a stump which is 24 inches in diameter. You can rent a gas powered stump grinder for between $ 100 and $ 200 per day depending on the size of the equipment. If you only have to remove one or two stumps, you're probably better off a professional but if you need to remove more or to share the experience with a neighbour, renting is definitely far more economical. You should make certain that the rental dealer explains the controls to you and shows you the safety precautions in operating the machine. Never use a stump grinder without wearing protection for the eyesight and hearing. You will also need a vehicle with a trailer hitch to to the grinder which has a weight of around 1000 lb but this is not available, your rental dealer will probably deliver the equipment to your house for an additional charge.
Start by using a shovel or a mattock to remove rocks from the base of the stump and this is important because the rocks can affect or damage the teeth on the cutting wheel. Next you will need a chainsaw to carefully trim the stump as close as possible to the ground and this is a step that you can skip and start with the grinder but things go much quicker this way. Use the hydraulic lever to lift the grinder wheel a few inches above the stump and drive the machine forward to position it directly over the front edge. Start the wheel spinning and then slowly lower rate of about 3 inches into the stump. The hydraulic lever can be used to swing the wheel from side to side to clear out the wood. After you are finished at least 4 inches, raise the wheel and advance it a few inches while repeating the process. When the machine is in operation, always position yourself at the control panel which is near the rear of the machine and safely away from the cutting wheel.
Slowly continue to grind your way to the other side of the stump stopping to check that the freshly dug hole is at least 4 inches below the ground. Collect the wood
chips and fill the crater with topsoil. Tamp down the soil and rake it lightly and then spread out an even layer of grass seed raking the seeds into the soil. Water the area and then cover the seats with a thick coating of mulch hay.
